GB/T 12361

Active

Steel die forgings—General specification

钢质模锻件 通用技术条件

Standard Type
GBT
ICS
77.140.85
CCS
J32
Status
现行
Issue Date
2016-12-13
Implementation
2017-07-01
Responsible Dept
国家标准委
Drafting Unit
国家标准委

📋 Scope / 适用范围 ai_extracted

This standard specifies the requirements, test methods, inspection rules, marking, packaging, storage, and preservation for automotive radiator electric fans (hereinafter referred to as fans). This standard applies to fans used in automotive engine radiator devices to drive loads and expel heat. Brushed (DC motor) fans incorporating electronic speed control controllers may also refer to this standard for implementation. This standard does not apply to the electronic modules of automotive radiator electric fans.

本标准规定了汽车散热器电动风扇(以下简称风扇)的要求、试验方法、检验规则、标志、包装、储存和保管。 本标准适用于汽车发动机散热器装置上驱动负载排出热量的风扇。含电子调速控制器的有刷(直流电动机)风扇也可参 照执行。 本标准不适用于汽车散热器电动风扇的电子模块。

📝 Foreword / 前言 ai_extracted

This standard is developed by referencing advanced foreign standards and relevant domestic standards such as QC/T 413-2002 "Basic Technical Conditions for Automotive Electrical Equipment". This standard is proposed by the National Technical Committee of Auto Standardization. This standard is under the jurisdiction of the National Technical Committee of Auto Standardization. The responsible drafting unit of this standard is: Shanghai Ri Yong-You Jie Automotive Electric Co., Ltd. The main drafters of this standard are: Zhang Meixue, Lin Hongmei, Zhou Weigang, Yang Zhongming. QC/T 773—2006 Cooling Fan Module Specification for Automobile

本标准参考国外先进标准及我国的QC/T 413-2002《汽车电气设备基本技术条件》等相关标准制定。 本标准由全国汽车标准化技术委员会提出。 本标准由全国汽车标准化技术委员会归口。 本标准负责起草单位：上海日用—友捷汽车电气有限公司。 本标准主要起草人：张梅学、林宏楣、周伟刚、杨忠明。 www.17jzw.com www.17bzw.cn www.17jzw.net www.3x888.com QC/T 773—2006 汽车散热器电动风扇技术条件 Cooling fan module specification for automobile

📚 References & Relations / 引用与关联

normative_reference DIVR25
normative_reference GB/T 1236
normative_reference GB/T 1236-1985
normative_reference GB/T 2423.17
normative_reference GB/T 3785-1983
normative_reference GB/T 4214-1984
normative_reference GB/T 7676.1
normative_reference GB/T2888
normative_reference GBL 8655
normative_reference IEC 68-2-11
normative_reference ISO 5801
normative_reference QC/T 29106
normative_reference QC/T 413-2002

🔗 Related Standards / 同类标准

GB/T 711-2008 Hot-rolled quality carbon structural steel plates, sheets and wide strips GB/T 710-2008 Hot-rolled quality carbon structural steel sheets and strips GB/T 20934-2007 Steel tie rod GB/T 702-1986 Hot-rolled round and square steels--Dimension,shape, weight and tolerance GB/T 911-1966 Hot-rolled and forged tool steel flats GB/T 3180-1982 Specification for medium manganese wear-resistant spheroidal iron castings GB/T 3522-1983 Cold-rolled quality carbon structural steel strips GB/T 346-1984 Galvanized low carbon steel wire for electric communications lines

Content extracted by AI. Not officially verified.